Code:
smartctl 5.41 2011-06-09 r3365 [i686-linux-3.1.0-3-grml-486] (local build)
Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION ===
Device Model: TOSHIBA MK5061GSY
Serial Number: 71P1B0HGB
LU WWN Device Id: 5 000039 369185aed
Firmware Version: MC102E
User Capacity: 500,107,862,016 bytes [500 GB]
Sector Size: 512 bytes logical/physical
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 8
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Sat Jul 21 21:04:18 2012 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 120) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 133) minutes.
SCT capabilities: (0x003f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0
2 Throughput_Performance 0x0005 100 100 050 Pre-fail Offline - 0
3 Spin_Up_Time 0x0027 100 100 001 Pre-fail Always - 1493
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 1232
5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0
7 Seek_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 100 100 050 Pre-fail Offline - 0
9 Power_On_Hours 0x0032 098 098 000 Old_age Always - 1066
10 Spin_Retry_Count 0x0033 124 100 030 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 1105
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 4
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 19
193 Load_Cycle_Count 0x0032 099 099 000 Old_age Always - 19319
194 Temperature_Celsius 0x0022 100 100 000 Old_age Always - 41 (Min/Max 10/48)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 100 100 000 Old_age Always - 10
198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
220 Disk_Shift 0x0002 100 100 000 Old_age Always - 8416
222 Loaded_Hours 0x0032 098 098 000 Old_age Always - 954
223 Load_Retry_Count 0x0032 100 100 000 Old_age Always - 0
224 Load_Friction 0x0022 100 100 000 Old_age Always - 0
226 Load-in_Time 0x0026 100 100 000 Old_age Always - 368
240 Head_Flying_Hours 0x0001 100 100 001 Pre-fail Offline - 0
SMART Error Log Version: 1
ATA Error Count: 758 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 758 occurred at disk power-on lifetime: 1065 hours (44 days + 9 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 41 02 29 08 ab 60 Error: UNC at LBA = 0x00ab0829 = 11208745
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 07 00 29 08 ab 40 00 00:08:02.075 READ FPDMA QUEUED
ef 10 02 00 00 00 a0 00 00:08:02.074 SET FEATURES [Reserved for Serial ATA]
27 00 00 00 00 00 e0 00 00:08:02.073 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 00 00:08:02.073 IDENTIFY DEVICE
ef 03 45 00 00 00 a0 00 00:08:02.073 SET FEATURES [Set transfer mode]
Error 757 occurred at disk power-on lifetime: 1065 hours (44 days + 9 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 41 02 29 08 ab 60 Error: UNC at LBA = 0x00ab0829 = 11208745
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 07 00 29 08 ab 40 00 00:07:58.975 READ FPDMA QUEUED
ef 10 02 00 00 00 a0 00 00:07:58.974 SET FEATURES [Reserved for Serial ATA]
27 00 00 00 00 00 e0 00 00:07:58.974 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 00 00:07:58.973 IDENTIFY DEVICE
ef 03 45 00 00 00 a0 00 00:07:58.973 SET FEATURES [Set transfer mode]
Error 756 occurred at disk power-on lifetime: 1065 hours (44 days + 9 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 41 02 29 08 ab 60 Error: UNC at LBA = 0x00ab0829 = 11208745
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 07 00 29 08 ab 40 00 00:07:55.549 READ FPDMA QUEUED
ef 10 02 00 00 00 a0 00 00:07:55.549 SET FEATURES [Reserved for Serial ATA]
27 00 00 00 00 00 e0 00 00:07:55.549 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 00 00:07:55.548 IDENTIFY DEVICE
ef 03 45 00 00 00 a0 00 00:07:55.548 SET FEATURES [Set transfer mode]
Error 755 occurred at disk power-on lifetime: 1065 hours (44 days + 9 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 41 02 29 08 ab 60 Error: UNC at LBA = 0x00ab0829 = 11208745
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 07 00 29 08 ab 40 00 00:07:52.417 READ FPDMA QUEUED
ef 10 02 00 00 00 a0 00 00:07:52.417 SET FEATURES [Reserved for Serial ATA]
27 00 00 00 00 00 e0 00 00:07:52.417 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 00 00:07:52.416 IDENTIFY DEVICE
ef 03 45 00 00 00 a0 00 00:07:52.416 SET FEATURES [Set transfer mode]
Error 754 occurred at disk power-on lifetime: 1065 hours (44 days + 9 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 41 02 29 08 ab 60 Error: UNC at LBA = 0x00ab0829 = 11208745
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 07 00 29 08 ab 40 00 00:07:49.225 READ FPDMA QUEUED
ef 10 02 00 00 00 a0 00 00:07:49.225 SET FEATURES [Reserved for Serial ATA]
27 00 00 00 00 00 e0 00 00:07:49.225 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 00 00:07:49.224 IDENTIFY DEVICE
ef 03 45 00 00 00 a0 00 00:07:49.224 SET FEATURES [Set transfer mode]
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 928 -
# 2 Short offline Completed without error 00% 843 -
# 3 Short offline Completed without error 00% 778 -
# 4 Short offline Completed without error 00% 722 -
# 5 Short offline Completed without error 00% 491 -
# 6 Short offline Completed without error 00% 20 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Jap. Die hatte nen Headcrash, wurde samt Laptop vom Tisch gefegt.